Find Laws Find Lawyers Free Legal Forms USA State Laws
CFR > Title 49 - Transportation > SUBTITLE B—Other Regulations Relating to Transportation > CHAPTER I—PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (Parts 105–199) > SUBCHAPTER C—HAZARDOUS MATERIALS REGULATIONS (Parts 171–181) > PART 171—GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS > SUBPART A—Applicability, General Requirements, and North American Shipments (§171.1 to §171.14) > 171.7—Reference material.

CFR

171.7—Reference material.

(a) Matter incorporated by reference— (1) General. There is incorporated, by reference in parts 170-189 of this subchapter, matter referred to that is not specifically set forth. This matter is hereby made a part of the regulations in parts 170-189 of this subchapter. The matter subject to change is incorporated only as it is in effect on the date of issuance of the regulation referring to that matter. The material listed in paragraph (a)(3) has been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is incorporated as it exists on the date of the approval and a notice of any change in the material will be published in the Federal Register. Matters referenced by footnote are included as part of the regulations of this subchapter.
(2) Accessibility of materials. All incorporated matter is available for inspection at:
(i) The Office of Hazardous Materials Safety, Office of Hazardous Materials Standards, East Building, PHH-10, 1200 New Jersey Avenue, SE., Washington, DC 20590-0001. For information on the availability of this material at PHH-10, call 1-800-467-4922, or go to: http://www.phmsa.dot.gov; and
(ii) The National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
(3) Table of material incorporated by reference. The following table sets forth material incorporated by reference. The first column lists the name and address of the organization from which the material is available and the name of the material. The second column lists the section(s) of this subchapter, other than § 171.7, in which the matter is referenced. The second column is presented for information only and may not be all inclusive.
Source and name of material 49 CFR reference
Air Transport Association of America, 1301 Pennsylvania Avenue, N.W., Washington, DC 20004-1707:
ATA Specification No. 300 Packaging of Airline Supplies, Revision 19, July 31, 1996 172.102.
The Aluminum Association, 420 Lexington Avenue, New York, NY 10017, telephone 301-645-0756, http://www.aluminum.org:
Aluminum Standards and Data, Seventh Edition, June 1982 172.102; 178.65.
Welding Aluminum: Theory and Practice, 2002 Fourth Edition 178.68
American National Standards Institute, Inc., 25 West 43rd Street, New York, NY 10036:
ANSI/ASHRAE 15-94, Safety Code for Mechanical Refrigeration 173.306; 173.307.
ANSI B16.5-77, Steel Pipe Flanges, Flanged Fittings 178.360-4.
ANSI N14.1 Uranium Hexafluoride—Packaging for Transport, 1971, 1982, 1987, 1990, 1995 and 2001 Editions 173.417; 173.420.
American Petroleum Institute, 1220 L Street, NW, Washington, D.C. 20005-4070:
API Recommended Practice Closures of Underground Petroleum Storage Tanks, 3rd Edition, March 1996 172.102.
American Pyrotechnics Association (APA), P.O. Box 30438, Bethesda, MD 20824, (301) 907-8181, www.americanpyro.com:
APA Standard 87-1, Standard for Construction and Approval for Transportation of Fireworks, Novelties, and Theatrical Pyrotechnics, December 1, 2001 version 173.56.
American Society of Mechanical Engineers, ASME International, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900, telephone 1-800-843-2763 or 1-973-882-1170, http://www.asme.org:
‘ASME Code’; ASME Code, Sections II (Parts A and B), V, VIII (Division 1), and IX of 1998 Edition of American Society of Mechanical Engineers Boiler and Pressure Vessel Code 172.102; 173.5b; 173.24b; 173.32; 173.306; 173.315; 173.318; 173.420; 178.245-1; 178.245-3; 178.245-4; 178.245-6; 178.245-7; 178.255-1; 178.255-2; 178.255-14; 178.255-15; 178.270-2; 178.270-3; 178.270-7; 178.270-9; 178.270-11; 178.270-12; 178.271-1; 178.272-1; 178.273; 178.274; 178.276; 178.277; 178.320; 178.337-1; 178.337-2; 178.337-3; 178.337-4; 178.337-6; 178.337-16; 178.337-18; 178.338-1; 178.338-2; 178.338-3; 178.338-4; 178.338-5; 178.338-6; 178.338-13; 178.338-16; 178.338-18; 178.338-19; 178.345-1; 178.345-2; 178.345-3; 178.345-4; 178.345-7; 178.345-14; 178.345-15; 178.346-1; 178.347-1; 178.348-1; 179.400-3; 180.407.
Code of Federal Regulations 86
Pipeline Transportation Systems for Liquid Hydrocarbons and other Liquids, Chapters II, III, IV, V and VI, ASME B31.4-1998 Edition 173.5a.
American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 1942, telephone (610) 832-9585, http://www.astm.org:
Noncurrent ASTM Standards are available from: Engineering Societies Library, 354 East 47th Street, New York, NY 10017
ASTM A 20/A 20M-93a Standard Specification for General Requirements for Steel Plates for Pressure Vessels 178.337-2; 179.102-4; 179.102-1; 179.102-17.
ASTM A 47-68 Malleable Iron Castings 179.200-15.
ASTM A 53, ASTM A 53/A 53M-06a Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless 173.5b.
ASTM A 106, ASTM A 106/A 106M-06a Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service 173.5b.
ASTM A 240/A 240M-99b Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels 178.57; 178.358-5; 179.100-7; 179.100-10; 179.102-1; 179.102-4; 179.102-17; 179.200-7; 179.201-5; 179.220-7; 179.300-7; 179.400-5.
Code of Federal Regulations 87
ASTM A 242-81 Standard Specification for High-Strength Low-Alloy Structural Steel 178.338-2.
ASTM A 262-93a Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels 179.100-7; 179.200-7; 179.201-4.
ASTM A 285-78 Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength 179.300-7.
ASTM A 300-58 Steel Plates for Pressure Vessels for Service at Low Temperatures 178.337-2.
ASTM A 302/A 302M-93 Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum Nickel 179.100-7; 179.200-7; 179.220-7.
ASTM A 333-67 Seamless and Welded Steel Pipe for Low-Temperature Service 178.45.
ASTM A 370-94 Standard Test 179.102-1; 179.102-4; Methods and Definitions for Mechanical Testing of Steel Products 179.102-17.
ASTM A 441-81 Standard Specification for High-Strength Low-Alloy Structural Manganese Vanadium Steel 178.338-2.
ASTM A 514-81 Standard Specification for High-Yield Strength Quenched and Tempered Alloy Steel Plate, Suitable for Welding 178.338-2.
ASTM A 515/A 515M-03 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service 179.300-7.
ASTM A 516/A 516M-90 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower-Temperature Service 178.337-2; 179.100-7; 179.102-1; 179.102-2; 179.102-4; 179.102-17; 179.200-7; 179.220-7; 179.300-7.
ASTM A 537/A 537M-91 Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel 179.100-7; 179.102-4; 179.102-17.
ASTM A 572-82 Standard Specification for High-Strength Low-Alloy Columbian-Vanadium Steels of Structural Quality 178.338-2.
ASTM A 588-81 Standard Specification for High-Strength Low-Alloy Structural Steel with 50 Ksi Minimum Yield Point to 4 in. Thick 178.338-2.
ASTM A 606-75 Standard Specification for Steel Sheet and Strip Hot- Rolled and Cold-Rolled, High-Strength, Low-Alloy, with Improved Atmospheric Corrosion Resistance, 1975 (Reapproved 1981) 178.338-2.
ASTM A 607-98 Standard Specification for Steel, Sheet and Strip, High-Strength, Low-Alloy, Columbium or Vanadium, or Both, Hot-Rolled and Cold-Rolled 178.338-2.
ASTM A 612-72a High Strength Steel Plates for Pressure Vessels for Moderate and Lower Temperature Service 178.337-2.
ASTM A 633-79a Standard Specification for Normalized High-Strength Low-Alloy Structural Steel, 1979 Edition 178.338-2.
ASTM A 715-81 Standard Specification for Steel Sheet and Strip, Hot-Rolled, High-Strength, Low-Alloy with Improved Formability, 1981 178.338-2.
ASTM A 1008/A 1008M—03 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High Strength Low-Alloy with Improved Formability 178.338-2; 178.345-2
ASTM A 1011/A 1011M—03a Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low Alloy and High Strength Low-Alloy with Improved Formability 178.338-2; 178.345-2
ASTM B 162-93a Standard Specification for Nickel Plate, Sheet, and Strip 173.249; 179.200-7.
ASTM B 209-93 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate 179.100-7; 179.200-7; 179.220-7.
ASTM B 221-76 Aluminum Alloy Extruded Bars, Rods, Shapes, and Tubes 178.46.
ASTM B 557-84 Tension Testing Wrought and Cast Aluminum and Magnesium-Alloy Products 178.46.
ASTM B 580-79 Standard Specification for Anodic Oxide Coatings on Aluminum, (Re-approved 2000) 173.316; 173.318; 178.338-17.
ASTM D 1238-90b Standard Test Method for Flow Rates of Thermoplastics for Extrusion Plastometer 173.225.
ASTM D 1709-01 Standard Text Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method 173.197.
ASTM D 1835-97 Standard Specification for Liquefied Petroleum (LP) Gases 180.209.
ASTM D 1838-64 Copper Strip Corrosion by Liquefied Petroleum (LP) Gases 173.315.
Code of Federal Regulations 88
ASTM D 1922-00a Standard Test Method for Propogation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method 173.197.
ASTM D 4206-96 Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus 173.120.
ASTM D 4359-90 Standard Test Method for Determining Whether a Material is a Liquid or a Solid 171.8.
ASTM E 8-99 Standard Test Methods for Tension Testing of Metallic Materials 178.36; 178.37; 178.38; 178.39; 178.44; 178.45; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.68.
ASTM E 23-98 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials 178.57.
ASTM E 112-88 Standard Test Methods for Determining Average Grain Size 178.44.
ASTM E 112-96 Standard Test Methods for Determining Average Grain Size, 1996 Edition 178.274; Part 178 , appendix A.
ASTM E 114-95 Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Examination by the Contact Method 178.45.
ASTM E 213-98 Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing 178.45.
American Water Works Association, 1010 Vermont Avenue, N.W., Suite 810, Washington, DC 20005:
AWWA Standard C207-55, Steel Pipe Flanges, 1955 178.360-4.
American Welding Society, 550 N.W. Le Jeune Road, Miami, Florida 33126:
AWS Code B 3.0; Standard Qualification Procedure; 1972 (FRB 3.0-41, rev. May 1973) 178.356-2, 178.358-2.
AWS Code D 1.0; Code for Welding in Building Construction (FR D 1.0-66, 1966) 178.356-2; 178.358-2.
Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001; telephone (877) 999-8824, http://www.aar.org/publications.com;
AAR Manual of Standards and Recommended Practices, Section C—Part III, Specifications for Tank Cars, Specification M-1002, (AAR Specifications for Tank Cars), December 2000 173.31; 174.63; 179.6; 179.7; 179.15; 179.16; 179.20; 179.22; 179.100-9; 179.100-10; 179.100-12; 179.100-13; 179.100-14; 179.100-18; 179.101-1; 179.102-1; 179.102-4; 179.102-17; 179.103-5; 179.200-7; 179.200-9; 179.200-10; 179.200-11; 179.200-13; 179.200-17; 179.200-22; 179.201-6; 179.220-6; 179.220-7; 179.220-10; 179.220-11; 179.220-14; 179.220-18; 179.220-26; 179.300-9; 179.300-10; 179.300-15; 179.300-17; 179.400-5; 179.400-6; 179.400-8; 179.400-11; 179.400-12; 179.400-15; 179.400-18; 179.400-20; 179.400-25; 180.509; 180.513; 180.515; 180.517.
Code of Federal Regulations 89
AAR Manual of Standards and Recommended Practices, Section I, Specially Equipped Freight Car and Intermodal Equipment, 1988 174.55; 174.63.
AAR Specifications for Design, Fabrication and Construction of Freight Cars, Volume 1, 1988 179.16.
Chlorine Institute, Inc., 1300 Wilson Boulevard, Arlington, VA 22209
AAR Standard 286; AAR Manual of Standards and Recommended Practices, Section C, Car Construction Fundamentals and Details, Standard S-286, Free/Unrestricted Interchange for 286,000 lb Gross Rail Load Cars (Adopted 2002; Revised: 2003, 2005, 2006) 179.13
Chlorine Institute Emergency Kit “A” for 100-lb. & 150 lb. Chlorine Cylinders (with the exception of repair method using Device 8 for side leaks), Edition 10, June 2003 173.3
Chlorine Institute Emergency Kit “B” for Chlorine Ton Containers (with the exception of repair method using Device 9 for side leaks), Edition 9, June 2003 173.3
Type 11/2 JQ 225, Dwg., H51970, Revision F, November 1996; or Type 11/2 JQ 225, Dwg. H50155, Revision H, November 1996 173.315.
Section 3, Pamphlet 57, Emergency Shut-Off Systems for Bulk Transfer of Chlorine, Edition 4, October 2003 177.840.
Section 3, Pamphlet 166, Angle Valve Guidelines for Chlorine Bulk Transportation, 1st Edition, October 2002 178.337-9.
Standard Chlorine Angle Valve Assembly, Dwg. 104-8, July 1993 178.337-9.
Excess Flow Valve with Removable Seat, Dwg. 101-7, July 1993 178.337-8.
Excess Flow Valve with Removable Basket, Dwg. 106-6, July 1993 178.337-8.
Standards for Housing and Manway Covers for Steel Cargo Tanks, Dwgs. 137-1 and 137-2, September 1, 1982 178.337-10.
Typical Manway Arrangement Chlorine Cargo Tank, Dwg 137-5, November 1996 178.337-10.
Canadian General Standards Board, Place du Portage III, 6B1 11 171.12
Laurier Street, Gatineau, Quebec, Canada K1A 1G6
National Standard of Canada (CAN/CGSB 43.147—2005) Construction, Modification, Qualification, Maintenance, and Selection and Use of Means of Containment for the Handling, Offering for Transport, or Transportation of Dangerous Goods by Rail
CGA Pamphlet C-3, Standards for Welding on Thin-Walled Steel Cylinders, 1994 178.47; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.65; 178.68; 180.211.
Code of Federal Regulations 90
CGA C-5, Cylinder Service Life—Seamless Steel High Pressure Cylinders, 1991 (reaffirmed 1995) 173.302a.
CGA Pamphlet C-6, Standards for Visual Inspection of Steel Compressed Gas Cylinders, 1993 173.3, 173.198, 180.205, 180.209, 180.211, 180.411, 180.519.
CGA Pamphlet C-6.1, Standards for Visual Inspection of High Pressure Aluminum Compressed Gas Cylinders, 2002, Fourth Edition 180.205; 180.209
CGA Pamphlet C-6.2, Guidelines for Visual Inspection and Requalification of Fiber Reinforced High Pressure Cylinders, 1996, Third Edition 180.205.
CGA Pamphlet C-6.3, Guidelines for Visual Inspection and Requalification of Low Pressure Aluminum Compressed Gas Cylinders, 1991 180.205; 180.209.
CGA C-7, Guide to Preparation of Precautionary Labeling and Marking of Compressed Gas Containers, Appendix A, issued 2004 (8th Edition) 172.400a.
CGA Pamphlet C-8, Standard for Requalification of DOT-3HT Cylinder Design, 1985 180.205; 180.209.
CGA Pamphlet C-11, Recommended Practices for Inspection of Compressed Gas Cylinders at Time of Manufacture, 2001, Third Edition 178.35.
CGA Pamphlet C-12, Qualification Procedure for Acetylene Cylinder Design, 1994 173.301; 173.303; 178.59; 178.60.
CGA Pamphlet C-13, Guidelines for Periodic Visual Inspection and Requalification of Acetylene Cylinders, 2000, Fourth Edition 173.303; 180.205; 180.209.
CGA Pamphlet C-14, Procedures for Fire Testing of DOT Cylinder Pressure Relief Device Systems, 1979 173.301; 173.323.
CGA Pamphlet G-2.2, Guideline Method for Determining Minimum of 0.2% Water in Anhydrous Ammonia, 1985, Second Edition, Reaffirmed 1997 173.315.
CGA Pamphlet G-4.1, Cleaning Equipment for Oxygen Service, 1985 178.338-15.
CGA Pamphlet P-20, Standard for the Classification of Toxic Gas Mixtures, 2003, Third Edition 173.115.
CGA Pamphlet P-20, Standard for the Classification of Toxic Gas Mixtures, 1995 173.115.
CGA S-1.1, Pressure Relief Device Standards—Part 1 —Cylinders for Compressed Gases, 2005 (with the exception of paragraph 9.1.1.1), Twelfth Edition 173.301, 173.304a 178.75.
CGA Pamphlet S-1.2, Safety Relief Device Standards Part 2 —Cargo and Portable Tanks for Compressed Gases, 1980 173.315; 173.318; 178.276; 178.277.
CGA S-7, Method for Selecting Pressure Relief Devices for Compressed Gas Mixtures in Cylinders, 2005 173.301.
CGA Technical Bulletin TB-2, Guidelines for Inspection and Repair of MC-330 and MC-331 Cargo Tanks, 1980 180.407; 180.413.
CGA Technical Bulletin TB-25, Design Considerations for Tube Trailers, 2008 Edition 173.301.
Department of Defense (DOD), 2461 Eisenhower Avenue, Alexandria, VA 22331:
DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1-47; DLAR 8220.1: Explosives Hazard Classification Procedures, January 1998 173.56.
Packaging of Hazardous Material, DLAD 4145.41/ AR 700-143/AFJI 24-210/NAVSUPINST 4030.55B/MCO 4030.40B, January 14, 2000 173.7
Department of Energy (USDOE), 100 Independence Avenue SW., Washington, DC 20545:
USDOE publications available from: Superintendent of Documents, Government Printing Office (GPO) or The National Technical Information Service (NTIS).
USDOE, CAPE-1662, Revision 1, and Supplement 1, Civilian Application Program Engineering Drawings, April 6, 1988 178.356-1; 178.356-2; 178.358-1; 178.358-2; 178.358-3; 178.358-4.
USDOE, Material and Equipment Specification No. SP-9, Rev. 1, and Supplement—Fire Resistant Phenolic Foam, March 28, 1968 178.356-2; 178.358-2.
USDOE, KSS-471, November 30, 1986—Proposal for Modifications to U.S. Department of Transportation Specification 21PF-1, Fire and Shock Resistant Phenolic Foam—Insulated Metal Overpack 178.358-1; 178.358-3.
General Services Administration, Specification Office, Room 6662, 7th and D Street, S.W., Washington, DC 20407:
Federal Specification RR-C-901D, Cylinders, Compressed Gas: Seamless Shatterproof, High Pressure DOT 3AA Steel, and 3AL Aluminum, February 21, 2003 (Superseding RR-C-901C, 1981) 173.302; 173.336; 173.337.
Institute of Makers of Explosives, 1120 19th Street NW., Suite 310, Washington, DC 20036-3605:
IME Safety Library Publication No. 22 (IME Standard 22), Recommendation for the Safe Transportation of Detonators in a Vehicle with Certain Other Explosive Materials, May 1993 173.63; 177.835.
International Atomic Energy Agency (IAEA), P.O. Box 100, Wagramer Strasse 5, A-1400 Vienna, Austria:
Also available from: Bernan Associates, 4611-F Assembly Drive, Lanham, MD 20706-4391, USA; or Renouf Publishing Company, Ltd., 812 Proctor Avenue, Ogdensburg, New York 13669, USA.
Code of Federal Regulations 91
IAEA, Regulations for the Safe Transport of Radioactive Material, (IAEA Regulations), 1996 Edition (Revised), No. TS-R-1 (ST-1, Revised) 171.22; 171.23; 171.26, 173.415, 173.416, 173.417, 173.473
International Civil Aviation Organization (“ICAO”), 999 University Street, Montréal, Quebec H3C 5H7, Canada, 1-514-954-8219, http://www.icao.int:
ICAO Technical Instructions available from: INTEREG, International Regulations, Publishing and Distribution Organization, P.O. Box 60105, Chicago, IL 60660.
Technical Instructions for the Safe Transport of Dangerous Goods by Air (“ICAO Technical Instructions”), 2009-2010 Edition 171.8; 171.22; 171.23; 171.24; 172.202; 172.401; 172.512; 172.602; 173.56; 173.320; 175.33; 178.3.
International Electrotechnical Commission (IEC) 3, rue de Varembé, P.O. Box 131, CH—1211, GENEVA 20, Switzerland:
Fuel cell technologies—Part 6-1 : Micro fuel cell power systems—Safety, IEC/PAS 62282-6-1:2006(E), First Edition 2006-02, with Corrigendum 1, First Edition 2007-04 § 175.10 .
International Maritime Organization (“IMO”), 4 Albert Embankment, London, SE1 7SR, United Kingdom or New York Nautical Instrument & Service Corporation, 140 West Broadway, New York, NY 10013, 44 (0) 20 7735 7611, http://www.imo.org:
International Convention for the Safety of Life at Sea, (“SOLAS”) 176.63, 176.84. Amendments 2002, Chapter II-2/Regulation 19, Consolidated Edition 2004.
International Maritime Dangerous Goods Code (“IMDG Code”), 2008 Edition, Incorporating Amendment 34-08 (English Edition), Volumes 1 and 2 171.22; 171.23; 171.25; 172.101 Appendix B; 172.202; 172.401; 172.502; 172.602; 173.21; 173.56; 176.2; 176.5; 176.11; 176.27; 176.30; 176.84; 178.3; 178.274.
International Organization for Standardization, Case Postale 56, CH-1211, Geneve 20, Switzerland, http://www.iso.org:
Also available from: ANSI 25, West 43rd Street, New York, NY 10036, 1-212-642-4900, http://www.ansi.org.
ISO 535-1991(E) Paper and board—Determination of water absorptiveness—Cobb method 178.516; 178.707; 178.708.
ISO 1496-1: 1990 (E)—Series 1 freight containers—Specification and testing, Part 1 : General cargo containers. Fifth Edition, (August 15, 1990) 173.411
ISO 1496-3—Series 1 freight containers—Specification and testing—Part 3 : Tank containers for liquids, gases and pressurized dry bulk, Fourth edition, March 1995, (E) 178.74; 178.75; 178.274.
ISO 2431-1984(E) Standard Cup Method 173.121.
ISO 2592-1973(E) Petroleum products—Determination of flash and fire points—Cleveland open cup method 173.120.
ISO 2919-1980(E) Sealed radioactive sources—Classification 173.469.
ISO 3036-1975(E) Board—Determination of puncture resistance 178.708.
ISO 3574-1986(E) Cold-reduced carbon steel sheet of commercial and drawing qualities 178.503; Part 178 , appendix C.
ISO 3807-2, Cylinders for acetylene—Basic requirements—Part 2 : Cylinders with fusible plugs, First edition, March 2000, (E) 173.303; 178.71.
ISO 4126-1 Safety valves—Part 1 : General Requirements, December 15, 1991, First Edition 178.274.
ISO 6406, Gas cylinders—Seamless steel gas cylinders—Periodic inspection and testing, Second edition, February 2005, (E) 180.207.
ISO 6892 Metallic materials—Tensile testing, July 15, 1984, First Edition 178.274.
ISO 7225, Gas cylinders—Precautionary labels, Second Edition, July 2005, (E) 178.71.
ISO 7866, Gas cylinders—Refillable seamless aluminum alloy gas cylinders—Design, construction and testing, First edition, June 1999, (E) 178.71.
ISO 8115 Cotton bales—Dimensions and density, 1986 Edition 172.102.
ISO 9809-1: Gas cylinders—Refillable seamless steel gas cylinders—Design, construction and testing—Part 1 : Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa., First edition, June 1999, (E) 178.37; 178.71; 178.75.
ISO 9809-2: Gas cylinders—Refillable seamless steel gas cylinders—Design, construction and testing—Part 2 : Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa., First edition, June 2000, (E) 178.71; 178.75.
ISO 9809-3: Gas cylinders—Refillable seamless steel gas cylinders—Design, construction and testing—Part 3 : Normalized steel cylinders, First edition, December 2000, (E) 178.71; 178.75.
ISO 9978:1992(E)—Radiation protection—Sealed radioactive sources—Leakage test methods. First Edition, (February 15, 1992) 173.469.
ISO 10156:1996, Gases and Gas Mixtures—Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets, Second edition, February 1996 (E) 173.115.
Code of Federal Regulations 92
ISO 10156-2:2005, Gas cylinders—Gases and gas mixtures—Part 2 : Determination of oxidizing ability of toxic and corrosive gases and gas mixtures, First edition, August 2005, (E) 173.115.
ISO 10297, Gas cylinders—Refillable gas cylinder valves—Specification and type testing, First edition, May 1999, (E) 173.301b, 178.71.
ISO 10461, Gas cylinders—Seamless aluminum—alloy gas cylinders—Periodic inspection and testing, Second edition, February 2005, (E) 180.207.
ISO 10462, Gas cylinders—Transportable cylinders for dissolved acetylene—Periodic inspection and maintenance, Second edition, February 2005, (E) 180.207.
ISO 11114-1, Transportable gas cylinders—Compatibility of cylinder and valve materials with gas contents—Part 1 : Metallic materials, First edition, October 1997, (E) 173.301b; 178.71.
ISO 11114-2, Transportable gas cylinders—Compatibility of cylinder and valve materials with gas contents—Part 2 : Non-metallic materials, First edition, December 2000, (E) 173.301b; 178.71.
ISO 11117, Gas cylinders—Valve protection caps and valve guards for industrial and medical gas cylinders—Design, construction and tests, First edition, August 1998, (E) 173.301b.
ISO 11118, Gas cylinders—Non-refillable metallic gas cylinders—Specification and test methods, First edition, October 1999, (E) 178.71.
ISO 11119-1, Gas cylinders—Gas cylinders of composite construction—Specification and test methods—Part 1 : Hoop-wrapped composite gas cylinders, First edition, May 2002, (E) 178.71.
ISO 11119-2, Gas cylinders—Gas cylinders of composite construction—Specification and test methods—Part 2 : Fully wrapped fibre reinforced composite gas cylinders with load-sharing metal liners, First edition, May 2002, (E) 178.71.
ISO 11119-3, Gas cylinders of composite construction—Specification and test methods—Part 3 : Fully wrapped fibre reinforced composite gas cylinders with non-load-sharing metallic or non-metallic liners, First edition, September 2002, (E) 178.71.
ISO 11120, Gas cylinders—Refillable seamless steel tubes of water capacity between 150 L and 3000 L—Design, construction and testing, First edition, March 1999, (E) 178.71; 178.75.
ISO 11621, Gas cylinders—Procedures for change of gas service, First edition, April 1997, (E) 173.302, 173.336, 173.337.
ISO 11623, Transportable gas cylinders—Periodic inspection and testing of composite gas cylinders, First edition, March 2002, (E) 180.207.
National Board of Boiler and Pressure Vessel Inspectors, 1055 Crupper Avenue, Columbus, Ohio 43229:
National Board Inspection Code, A Manual for Boiler and Pressure Vessel Inspectors, NB-23, 1992 Edition 180.413.
National Fire Protection Association, Batterymarch Park, Quincy, MA 02269:
NFPA 58-Liquefied Petroleum Gas Code, 2001 Edition 173.315.
National Institute of Standards and Technology, Department of Commerce, 5285 Port Royal Road, Springfield, VA 22151:
USDC, NBS Handbook H-28 (1957), 1957 Handbook of Screw-Thread Standards for Federal Services, December 1966 Edition 179.2; 178.45; 178.46.
Organization for Economic Cooperation and Development (OECD), OECD Publications and Information Center, 2001 L Street, N.W., Suite 700, Washington, DC 20036:
OECD Guideline for Testing of Chemicals, No. 404 “Acute Dermal Irritation/Corrosion,” 1992 173.137.
Transport Canada, TDG Canadian Government Publishing Center, Supply and Services, Canada, Ottawa, Ontario, Canada K1A 059, 416-973-1868, http://www.tc.gc.ca:
Transportation of Dangerous Goods Regulations (Transport Canada TDG Regulations), August 2001 including Clear Language Amendments SOR 2001-286, Amendment 1 (SOR/2002-306) August 8, 2002; Amendment 2 (SOR/2003-273) July 24, 2003; Amendment 3 (SOR/2003-400) December 3, 2003; Amendment 4 (SOR/2005-216) July 13, 2005; Amendment 5 (SOR/2005-279) September 21, 2005; and subsection 4.18(5) of Amendment 6 (SOR/2008-34) February 7, 2008 171.12; 171.22; 171.23; 172.401; 172.502; 172.519; 172.602; 173.31; 173.32; 173.33.
Truck Trailer Manufacturers Association, 1020 Princess Street, Alexandria, Virginia 22314:
TTMA RP No. 61-98, Performance of manhole and/or Fill Opening Assemblies on MC 306, DOT 406, Non-ASME MC 312 and Non-ASME DOT 412 Cargo Tanks, June 1, 1998 180.405.
TTMA RP No. 81-97, Performance of Spring Loaded Pressure Relief Valves on MC 306, MC 307, MC 312, DOT 406, DOT 407, and DOT 412 Tanks, July 1, 1997 Edition 178.345-10; 178.346-3.
TTMA TB No. 107, Procedure for Testing In-Service Unmarked and/or Uncertified MC 306 and Non-ASME MC 312 Type Cargo Tank Manhole Covers, June 1, 1998 Edition 180.405.
United Nations, Publications, 2 United Nations Plaza, Room DC2-853, New York, NY 10017, 1-212-963-8302, http://unp.un.org.
UN Recommendations on the Transport of Dangerous Goods, Fifteenth revised edition (2007). Volumes I and II 171.8; 171.12; 171.22; 171.23; 172.202; 172.401; 172.502; 173.22; 173.24; 173.24b; 173.40; 173.56; 173.192; 173.197; 173.302b; 173.304b; 178.75; 178.274; 178.801.
UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, Fourth revised edition, (2003), and Addendum 2, (2004) 172.102; 173.21; 173.56; 173.57; 173.58; 173.115; 173.124; 173.125; 173.127; 173.128; 173.137; 173.185; Part 173 , appendix H; 178.274.
Code of Federal Regulations 93
United States Enrichment Corporation, Inc. (USEC):
USEC Inc., 6903 Rockledge Drive, Bethesda, MD 20817
USEC-651—Good Handling Practices for Uranium Hexafluoride, Revision 8, January 1999 173.417
(b) List of informational materials not requiring incorporation by reference. The materials listed in this paragraph do not require approval for incorporation by reference and are included for informational purposes. These materials may be used as noted in those sections in which the material is referenced.
Source and name of material 49 CFR reference
American Biological Safety Association
1202 Allanson Road, Mundelein, IL 60060
Risk Group Classification for Infectious Agents, 1998 173.134
American Institute of Chemical Engineers (AIChE),
3 Park Avenue New York, NY 10016-5991
Process Safety Progress Journal, Vol. 21, No. 2
Example of a Test Method for Venting Sizing: OPPSD/SPI Methodology Note to § 173. 225(h)(3)(vi).
American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428:
Noncurrent ASTM Standards are available from: Engineering Societies Library, 354 East 47th Street, New York, NY 10017
ASTM E 380-89 Standards for Metric Practice 171.10
Association of American Railroads,
American Railroads Building, 50 F Street, NW., Washington, DC 20001
AAR Catalog Nos. SE60CHT; SE60CC; SE60CHTE; SE60CE; SE60DC; SE60DE 179.14
AAR Catalog Nos. SE67CC; SE67CE; SE67BHT; SE67BC; SE67BHTE; SE67BE 179.14
AAR Catalog Nos. SE68BHT; SE68BC; SE68BHTE; SE68BE 179.14
AAR Catalog Nos. SE69AHTE; SE69AE 179.14
AAR Catalog Nos. SF70CHT; SF70CC; SF70CHTE; SF70CE 179.14
AAR Catalog Nos. SF73AC; SF73AE; SF73AHT; SF73AHTE 179.14
AAR Catalog Nos. SF79CHT; SF79CC; SF79CHTE; SF79CE 179.14
Bureau of Explosives,
Hazardous Materials Systems (BOE), Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001
Fetterley's Formula (The Determination of the Relief Dimensions for Safety Valves on Containers in which Liquefied gas is
Tips