CFR
- Title 1 - General Provisions
- Title 2 - Grants and Agreements
- Title 3 - The President
- Title 4 - Accounts
- Title 5 - Administrative Personnel
- Title 6 - Domestic Security
- Title 7 - Agriculture
- Title 8 - Aliens and Nationality
- Title 9 - Animals and Animal Products
- Title 10 - Energy
- Title 11 - Federal Elections
- Title 12 - Banks and Banking
- Title 13 - Business Credit and Assistance
- Title 14 - Aeronautics and Space
- Title 15 - Commerce and Foreign Trade
- Title 16 - Commercial Practices
- Title 17 - Commodity and Securities Exchanges
- Title 18 - Conservation of Power and Water Resources
- Title 19 - Customs Duties
- Title 20 - Employees' Benefits
- Title 21 - Food and Drugs
- Title 22 - Foreign Relations
- Title 23 - Highways
- Title 24 - Housing and Urban Development
- Title 25 - Indians
- Title 26 - Internal Revenue
- Title 27 - Alcohol, Tobacco Products and Firearms
- Title 28 - Judicial Administration
- Title 29 - Labor
- Title 30 - Mineral Resources
- Title 31 - Money and Finance: Treasury
- Title 32 - National Defense
- Title 33 - Navigation and Navigable Waters
- Title 34 - Education
- Title 35 - Panama Canal
- Title 36 - Parks, Forests, and Public Property
- Title 37 - Patents, Trademarks, and Copyrights
- Title 38 - Pensions, Bonuses, and Veterans' Relief
- Title 39 - Postal Service
- Title 40 - Protection of Environment
- Title 41 - Public Contracts and Property Management
- Title 42 - Public Health
- Title 43 - Public Lands: Interior
- Title 44 - Emergency Management and Assistance
- Title 45 - Public Welfare
- Title 46 - Shipping
- Title 47 - Telecommunication
- Title 48 - Federal Acquisition Regulations System
- Title 49 - Transportation
- Title 50 - Wildlife and Fisheries
1926.1001—Minimum performance criteria for rollover protective structures for designated scrapers, loaders, dozers, graders, and crawler tractors.
(a) General.
This section prescribes minimum performance criteria for rollover protective structures (ROPS) for rubber-tired self-propelled scrapers; rubber-tired front-end loaders and rubber-tired dozers; crawler tractors, and crawler-type loaders, and motor graders. The vehicle and ROPS as a system shall have the structural characteristics prescribed in paragraph (f) of this section for each type of machine described in this paragraph.
(b)
The static laboratory test prescribed herein will determine the adequacy of the structures used to protect the operator under the following conditions:
(1)
For rubber-tired self-propelled scrapers, rubber-tired front-end loaders, and rubber-tired dozers: Operating between 0 and 10 miles per hour over hard clay where rollover would be limited to a maximum roll angle of 360° down a slope of 30° maximum.
(2)
For motor graders: Operating between 0 and 10 miles per hour over hard clay where rollover would be limited to 360° down a slope of 30° maximum.
(3)
For crawler tractors and crawler-type loaders: Operating between 0 and 10 miles per hour over hard clay where rollover would be limited to a maximum roll angle of 360° down a slope of 45°.
(i)
Material, equipment, and tiedown means adequate to insure that the ROPS and its vehicle frame absorb the applied energy.
(ii)
Equipment necessary to measure and apply loads to the ROPS. Adequate means to measure deflections and lengths should also be provided.
(iii)
Recommended, but not mandatory, types of test setups are illustrated in Figure W-1 for all types of equipment to which this section applies; and in Figure W-2 for rubber-tired self-propelled scrapers; Figure W-3 for rubber-tired front-end loaders, rubber-tired dozers, and motor graders; and Figure W-4 for crawler tractors and crawler-type loaders.
(2)
Table W-1 contains a listing of the required apparatus for all types of equipment described in paragraph (a) of this section.
| Means to measure | Accuracy |
|---|---|
| Deflection of ROPS, inches | ±5% of deflection measured. |
| Vehicle weight, pounds | ±5% of the weight measured. |
| Force applied to frame, pounds | ±5% of force measured. |
| Dimensions of critical zone, inches | ±0.5 in. |
(d) Vehicle condition.
The ROPS to be tested must be attached to the vehicle structure in the same manner as it will be attached during vehicle use. A totally assembled vehicle is not required. However, the vehicle structure and frame which support the ROPS must represent the actual vehicle installation. All normally detachable windows, panels, or nonstructural fittings shall be removed so that they do not contribute to the strength of the ROPS.
(1)
Energy absorbing capabilities of ROPS shall be verified when loaded laterally by incrementally applying a distributed load to the longitudinal outside top member of the ROPS, as shown in Figure W-1, W-2, or W-3, as applicable. The distributed load must be applied so as to result in approximately uniform deflection of the ROPS. The load increments should correspond with approximately 0.5 in. ROPS deflection increment in the direction of the load application, measured at the ROPS top edge. Should the operator's seat be offcenter, the load shall be applied on the offcenter side. For each applied load increment, the total load (lb.) versus corresponding deflection (in.) shall be plotted, and the area under the load -deflection curve shall be calculated. This area is equal to the energy (in.-lb.) absorbed by the ROPS. For a typical load-deflection curve and calculation method, see Figure W-5.
Code of Federal Regulations
Code of Federal Regulations
Code of Federal Regulations
495
Code of Federal Regulations
Code of Federal Regulations
Code of Federal Regulations
496
Incremental loading shall be continued until the ROPS has absorbed the amount of energy and the minimum applied load specified under paragraph (f) of this section has been reached or surpassed.
(2)
To cover the possibility of the vehicle coming to rest on its top, the support capability shall be verified by applying a distributed vertical load to the top of the ROPS so as to result in approximately uniform deflection (see Figure W-1). The load magnitude is specified in paragraph (f)(2)(iii) of this section.
(3)
The low temperature impact strength of the material used in the ROPS shall be verified by suitable material tests or material certification (see paragraph (f)(2)(iv) of this section).
Code of Federal Regulations
(f) Performance requirements—
(1) General performance requirements.
No repairs or straightening of any member shall be carried out between each prescribed test.
(ii)
During each test, no part of the ROPS shall enter the critical zone as detailed in SAE J397 (1969). Deformation of the ROPS shall not allow the plane of the ground to enter this zone.
(2) Specific performance requirements.
(i)
The energy requirement for purposes of meeting the requirements of paragraph (e)(1) of this section is to be determined by referring to the plot of the energy versus weight of vehicle (see Figure W-6 for rubber-tired self-propelled scrapers; Figure W-7 for rubber-tired front-end loaders and rubber-tired dozers; Figure W-8 for crawler tractors and crawler-type loaders; and Figure W-9 for motor graders). For purposes of this section, force and weight are measured as pounds (lb.); energy (U) is measured as inch-pounds.
Code of Federal Regulations
Code of Federal Regulations
497
(ii)
The applied load must attain at least a value which is determined by multiplying the vehicle weight by the corresponding factor shown in Figure W-10 for rubber-tired self-propelled scrapers; in Figure W-11 for rubber-tired front-end loaders and rubber-tired dozers; in Figure W-12 for crawler tractors and crawler-type loaders; and in Figure W-13 for motor graders.
(iii)
The load magnitude for purposes of compliance with paragraph (e)(2) of this section is equal to the vehicle weight. The test of load magnitude shall only be made after the requirements of paragraph (f)(2)(i) of this section are met.
Code of Federal Regulations
(iv)
Material used in the ROPS must have the capability of performing at zero degrees Fahrenheit, or exhibit Charpy V notch impact strength of 8 foot-pounds at minus 20 °Fahrenheit.
This is a standard Charpy specimen as described in American Society of Testing and Materials A 370, Methods and Definitions for Mechanical Testing of Steel Products (available at each Regional Office of the Occupational Safety and Health Administration). The purpose of this requirement is to reduce the tendency of brittle fracture associated with dynamic loading, low temperature operation, and stress raisers which cannot be entirely avoided on welded structures.
Code of Federal Regulations
Code of Federal Regulations
498
Code of Federal Regulations
(g) Definitions.
For purposes of this section, “vehicle weight” means the manufacturer's maximum weight of the prime mover for rubber-tired self-propelled scrapers. For other types of equipment to which this section applies, “vehicle weight” means the manufacturer's maximum recommended weight of the vehicle plus the heaviest attachment.
Code of Federal Regulations
Code of Federal Regulations
Code of Federal Regulations
Code of Federal Regulations
499
Code of Federal Regulations
(h) Source of standard.
This standard is derived from, and restates, the following Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll-Over Protective Structure for Rubber-Tired, Self-Propelled Scrapers; SAE J394, Minimum Performance Criteria for Roll-Over Protective Structure for Rubber-Tired Front End Loaders and Rubber-Tired Dozers; SAE J395, Minimum Performance Criteria for Roll-Over Protective Structure for Crawler Tractors and Crawler-Type Loaders; and SAE J396, Minimum Performance Criteria for Roll-Over Protective Structure for Motor Graders. These recommended practices shall be resorted to in the event that questions of interpretation arise. The recommended practices appear in the 1971 SAE Handbook, which may be examined in each of the Regional Offices of the Occupational Safety and Health Administration.
Tips